The second-hand vacuum oven of stainless steel double spiral cone mixer sold in Hebei Province is a box type drying equipment for drying materials under negative pressure. It is to use vacuum pump to pump air and dehumidify, so as to form a vacuum state in the working room, reduce the boiling point of water, and accelerate the drying speed. Hocheck vacuum oven can get higher drying rate at lower temperature and make full use of heat. It is mainly suitable for drying heat sensitive materials, materials containing capacity agent and solvent to be recovered. Disinfection treatment can be carried out before drying, and no sundries can be mixed in the drying process. The dryer belongs to static vacuum dryer, so the formation of drying materials will not be damaged. Heating methods: steam, hot water, heat transfer oil, electric heating. The vacuum oven is specially designed for drying heat sensitive, decomposable and oxidizable substances, which can be filled with inert gas. Especially, some articles with complex components can be dried quickly. The product has the following characteristics: 1, cuboid studio, to maximize the effective volume, microcomputer temperature controller, accurate temperature control. 2. Toughened, bulletproof double glass door, observe the objects in the studio at a glance. 3. The tightness and tightness of the box can be adjusted. The silicone rubber door seal ring with integral molding ensures high vacuum degree in the box. 4. The workroom is made of stainless steel plate (or wire drawing board), which ensures the durability of the products. 5. Storage, heating, testing and drying are carried out in the absence of oxygen or filled with inert gas, so they will not oxidize. 6. Compared with the traditional drying oven, the heating time is reduced by more than 50%. Because the heat energy of vacuum oven is provided by electric power, and the wet articles will conduct electricity, so be careful not to have leakage in use. Therefore, the general oven should be grounded for safety. If there is no ground wire, make sure that there is no leakage in the oven; if there is slight leakage, try to pull out the socket and insert the pin in the opposite direction. If there is no leakage, you can use it carefully. If there is still leakage, it should be stopped immediately. The size of drying plate is 460mm * 640mm * 45mm (width, depth and height). It can be interchanged with vacuum drying oven and ordinary oven. The difference between vacuum oven and ordinary oven is that it works under negative pressure, with less oxygen content, which can reduce or eliminate oxidation reaction. Under negative pressure, the boiling point of solvent is reduced to avoid high temperature drying damaging the quality of materials. If the solvent is harmful or valuable gas, it can be condensed and recovered. Disadvantages: it is difficult to control the temperature uniformity and property. If it is necessary to control the uniformity, multilayer laminates must be made and heated independently. There are also vacuum box with fan, first vacuum and then filled with nitrogen heating. This reduces oxidation and ensures uniformity by blowing. But there is no way to lower the boiling point of the solvent. General oven: the material is dried by electric heating plus air blowing and heat exchange with hot air. Generally, compared with vacuum drying, the cost is lower and the operation cost is lower. Points for attention in selecting vacuum pump of vacuum oven: 1. Select appropriate vacuum pump according to the size of space (internal dimension of 1000 liter vacuum box); 2. Pumping speed. It is recommended to reach the required vacuum degree within 2-3 minutes (pay attention to the limit vacuum of vacuum pump) 3. When choosing the vacuum pump, you should pay attention to the temperature in the box and the characteristics of the materials to be dried (whether they are inflammable, explosive or corrosive, etc.) 4. The vacuum pump reference table (common model) vacuum oven is composed of high vacuum vacuum pump, box, working room, electric heater and digital thermometer. It can work stably under the set vacuum condition. It is suitable for vacuum drying of medicine, chemical industry, electronics, apparatus, materials and parts. The shell of the box is sprayed with cold binding plate, which is beautiful and pleasing to the eye. The inner box is treated with stainless steel plate welding and pressure resistance process, with silica gel sealing pad on the door to ensure the air tightness of the box. Glass fiber insulation is used to provide high-efficiency heat insulation and save energy consumption. The heating plate is installed on the four sides of the inner box to ensure the temperature uniformity.